1997 Super Sport - Red/Black AIR - Work in Progress ---Lots of Photos

[Brichter14]

Exterior with thru hulls for drain/vent. Painted them red cuz I liked it.




Rocker switches installed





That's it. All done.

I took it to the ramp and everything works great except I can't fill the ski locker while I'm filling rear sacks. Just gonna fill that one at the ramp and fill the rears once we get to riding spot. Making lemonade.

[Brichter14]

Switch housing installed



Wiring the switches. Wires go from pumps to switch. Then switches are powered through the fuse block I installed earlier.



Replaced the fuel tank cover



Pics of vdrive storage with dividers and all hoses/wires ran

[Brichter14]

Running hoses across gas tank to the rear of the boat



Hoses on pumps. Heat gun>hair dryer.



Template for vents/drains. Order from left to right or back to front goes left bag, right bag, locker(front ) bag



Traced area for switches



Some bags with hoses

[Brichter14]

Big hole in the bottom of my boat



Picture of the mushroom thru hull



With the street elbow and ball valve



Started plumbing hoses. I use a t1200 tsunami pump for fill and a 1" hose. Use t800 for drain and 3/4" hose. I used Y fittings to connect my drain and vent lines. Check valve on vent line.



Pic of pumps

[Brichter14]

Started my ballast project last night and finished it a few hours ago.

Here's what happened.

All this stuff came in from wakemakers. Those guys are awesome.

I was originally going to make a manifold out of 3/4" T fittings but when I saw them I changed my mind



So I went to the store and made a manifold out of 1 1/4" PVC. Which is e same size as my one and only thru hull



What I originally had in my head and what actually would work



More to follow.

[Brichter14]

Started prepping for tomorrow's delivery

[Brichter14]

Teaser for my weekend project.

[Brichter14]

Beautiful ride!!!! Is that an old Obrien wakeboard in the front storage area? I have that one mounted on my wall as it was my first board. Can you surf with that board? How do you plan on setting up the ballasts? I am looking at a really clean 1995 Super Sport and trying to figure out the best way to set up a ballast system. Secondly, do you know a good place to order decals?

Ya it's an old obrien. We tried surfing with it but it isn't buoyant enough. Ballast bags are two 750s in engine compartment and the flyhigh locker/backseat bag in locker that's a 580 bag. Ill have 300 in lead/iron weights in the bow. Go to www.nautiqueparts.com for decals.

I'm doing an aerator pump system for ballast instead of reversible pumps for these reasons.
1. Cost
2. Speed
3. Ability to run dry
4. I like watching water drain out the side.
5. Less amp draw, I gots 1 battery.

[Brichter14]

More pics of amp install




I then mounted my fuse block for my upcoming ballast install. Gonna have 6 aerator pumps wired to it.

[Brichter14]

New stuff!

Got a new headunit that let's you put your iPhone or iPod INSIDE the headunit. Also got a transom remote for it. Had to drill a 3.25" hole in the transom. That was fun with a Dremel tool!



I also got my sub in and installed my amp. The sub is a DVC alpine type S. I wired it in parallel to drop the impedance down to 2 ohms. The amp is a polk 5000.5.

[Wakerider90]

Beautiful ride!!!! Is that an old Obrien wakeboard in the front storage area? I have that one mounted on my wall as it was my first board. Can you surf with that board? How do you plan on setting up the ballasts? I am looking at a really clean 1995 Super Sport and trying to figure out the best way to set up a ballast system. Secondly, do you know a good place to order decals?

[Brichter14]

Had some goodies come in the mail today.

[Brichter14]

Yeah it fits but I gotta move some of the wires and gas lines over slightly. I don't have a heater so no problems there. Sub should be here by fri. I will get pics then

[moto132]

Have you test fit the enclosure yet? In my 97 i have a heater and there is no way that enclosure would fit with the kick plate in the stock location. I am building a box right now, hopefully finishing it wednesday but i had to move my kick plate forward 7 inches to clear my heater. I also have my heater tubes mounted in my kick plate. Curious to see how it works out! Boat looks good so far!

[Brichter14]

Finished the engine dividers. Should be ready for ballast now. Also finished my enclosed kick panel sub box. Sub is on order.