wakeshapers

[pSchwade]

Lots of great discussion going on here. Typically we recommend placing the Delta so its at the waterline when the boat is fully ballasted ready for surfing. The 230 looks like there is a good space about even with the swim platform, that's usually a really good spot to start. Someone asked about listing. That's one great feature of the Delta. There is no need to list. We recommend starting with the boat evenly ballasted side to side.

Im sure there isnt a NEED to list the boat, but since you cant switch sides mid run (like the NSS) I imagine that most people will still list their boats as much as they do now.

[missionbg]

Lots of great discussion going on here. Typically we recommend placing the Delta so its at the waterline when the boat is fully ballasted ready for surfing. The 230 looks like there is a good space about even with the swim platform, that's usually a really good spot to start. Someone asked about listing. That's one great feature of the Delta. There is no need to list. We recommend starting with the boat evenly ballasted side to side.

[nyryan2001]

Mark, let me know if I can demo on my G23. I'll post pics and give it an honest review.

$500 is a steep gamble when comparability with existing sirf systems is in question. I'd even pay to get reimbursed when I return a few weeks later.

[pSchwade]

It looks like the 210 and the 220 will probably be ok, but the flat section on the 230 could be half way out of the water with a lot of list

Here's a 220:

[NautiqueOasis]

I am interest in a group buy also

[Super B]

Looking at pics of that hull, it looks like there are several steps near the bottom and then some geometry near the rub rail. In general is it accurate to say that the solid colored section that contains the Nautique graphics is flat near the transom? That would be the area that we would be attaching. From what I can see, I think the Delta would work great. We tested this on a Xstar that has the big cut outs at the bottom and it worked great. See our website for a video. Hope this helps. Anyone near Minnetonka MN?

I'm not too far away... But, my boat is up north at the cabin. I could certainly bring it down if you needed to test fit on a '09 211...

[bdisney3]

Here's a shot of a 210:


And here's a shot of a 230:



Does that help?

[missionbg]

Looking at pics of that hull, it looks like there are several steps near the bottom and then some geometry near the rub rail. In general is it accurate to say that the solid colored section that contains the Nautique graphics is flat near the transom? That would be the area that we would be attaching. From what I can see, I think the Delta would work great. We tested this on a Xstar that has the big cut outs at the bottom and it worked great. See our website for a video. Hope this helps. Anyone near Minnetonka MN?

[BoardSkier]

Another question is whether the suction cups will fit a stepped hull. What are the diameters of the suction cups?


Sent from my iPhone using Tapatalk

[funkster]

Hi Guy/Gals,

Mark here from Mission Boat Gear.
Glad to hear you discussing our new Delta Product. If there is anything I can answer for you? Shout it out.
Everyone who has seen Delta in action has loved it.

Mark

Mark, looks like an awesome product! One of the main questions in this thread is can you provide a group buy? Looks like there is already 10-11 people that would be in if that was an option.

[bdisney3]

missionbg - several people in this thread (including me) have wondered if the Delta will fit the "stepped hulls" many of us have (I have a 2009 Super Air Nautique 210 (same hull for 07-13 I believe). Do you know?

[missionbg]

Hi Guy/Gals,

Mark here from Mission Boat Gear.
Glad to hear you discussing our new Delta Product. If there is anything I can answer for you? Shout it out.
Everyone who has seen Delta in action has loved it.

Mark

[mlsurfco]

I know these guys. I will see what they say about a group buy.

[pSchwade]

It looks like they 3D printed their injection molding cavity... they could have at least sanded away the layer lines.

[pokesgrad02]

I'm in for group buy as well